How To Repair Ice Dispenser Kenmore

If you are facing Kenmore Ice maker Not Making Ice, then at that place are a few possible bug at mitt. But before you determine your water ice maker is lacking, allow's accept a look at some of the issues that tin cause ice not to manipulate. You lot might not need to get a new i yet.

Historically, ice makers built into refrigerators lasted the boilerplate life of the refrigerator. Merely now, manufacturers are calculation more features to the ice makers, which decreases their lifespan to about five years.

After a few years, mechanical and electrical problems may come. In many cases, these problems are like shooting fish in a barrel to set yourself. If you have a few minutes to fix these small issues, you can save hundreds of dollars over time.

1. Faulty H2o Inlet Valve

The h2o inlet valve opens to supply water to the dispenser and water ice maker. If it malfunctions, or if there is bereft pressure, information technology volition non be able to provide water to either of them. As a issue, the ice maker will not produce water ice.

If your valve solenoids are having mechanical or electric bug, your valve won't open water to the ice maker. A mechanical failure can be acquired by mineral deposits building up and preventing the valve from opening. An electric failure might be acquired by burnt coils on the valve.

Keep in mind that the valve needs xx psi to piece of work. To test this, you need to mensurate the water pressure. If it's at least xx psi, check to see if at that place is electricity going to the h2o inlet valve. If the water inlet valve has power and is getting more than 20 psi of water pressure, merely the Kenmore ice maker however won't fill with water, chances are you lot demand to supplant the water inlet valve.

Depending on the upshot, the inlet valve could need to be replaced. The Multimeter can examination the solenoid coils for continuity. If i or more coils are having bug, the inlet valve will need to exist repaired or replaced. If there is a humming audio coming from the valve, only no water comes out, try cleaning the solenoid again.

2. Wrong Temperature Setting

The ice maker won't make cubes if the freezer is too warm. The temperature should be at -v degrees Fahrenheit (-eighteen degrees Celsius), or lower.

If your freezer is staying above 15 degrees Fahrenheit or -nine degrees Celcius, something might exist wrong with the appliance. Droppings on the coils might be keeping the appliance from properly cooling.

3. Frozen Evaporator Coils

When the refrigeration Evaporator coils are frosted, information technology means there is a defect in the defrost system. There are iv possible causes of this failure: the defrost thermostat, control board, heater, or cold temp sensor.

The evaporator fan motor fails to properly broadcast the air inside your freezer, or frosted evaporator coils restrict airflow, causing your ice maker to malfunction.

An ice maker's inability to work correctly might be due to an evaporator motor that is non working or frozen evaporator coils. This will cause the temperature of the freezer to increase, which in turn will cause the water ice maker to finish functioning properly.

4. Broken Door Switch

The door switch is what turns the water ice and water dispenser off when the refrigerator door is open. If the switch fails, it won't turn on even if you push the buttons.

Checking the freezer door switch is like shooting fish in a barrel. All you need to do is push it, and if the low-cal goes off, that means the switch is working. If the light stays on, then there'southward a malfunction with the switch.

To find out if it'southward broken, use a multimeter to see if it has continuity. If information technology doesn't, replace information technology.

v. Low Water Pressure

A h2o inlet valve needs about 20 psi of water pressure per square inch to work correctly. This ways that if you plough off the h2o supply, disconnect the supply line from the inlet valve and concur the line over a bucket, you can see for yourself if the line has enough pressure to operate properly.

Information technology sounds like the h2o is not flowing the way it'south supposed to. Permit's turn the h2o supply on and run across if nosotros tin can guess what the problem is. If there is a low flow of water, it may be an issue with the pipes or valves.

6. Kenmore Icemaker Mold Thermostat

Monitoring the temperature of your ice maker is essential for making water ice cubes. This thermostat makes sure that once the temperature is right, the ice maker will eject the water ice cubes and refill the mold with water. If this thermostat is defective, the ice maker will finish making ice.

To troubleshoot a thermostat that may be defective, check for continuity using a multimeter. If there's no continuity, replace information technology.

The ice maker won't make water ice if information technology is not cold enough. That's because if the temperature is over 20 degrees Fahrenheit, the thermostat contacts volition open and the water will catamenia freely through the mold. The temperature must be below 20 degrees to close the contacts and so the h2o freezes and becomes ice.

Source: https://kcscfm.com/kenmore-ice-maker-not-making-ice/

Posted by: lewistherelies.blogspot.com

Share this post